The Things I Like

John's blog on Art, Technology, design and more!

RSS 2.0

August 14th, 2018

Translucent TPU first layer has to be my favorite

submitted by /u/takeshikun [link] [comments] from 3D printing news https://ift.tt/2KSbj8U via RSS

Tags: , , , ,

Posted in 3D, 3DPrinting, news, reddit | No Comments »

If it works it works [Painful]

submitted by /u/Thombis [link] [comments] from 3D printing news https://ift.tt/2BalTZp via RSS

Tags: , , , ,

Posted in 3D, 3DPrinting, news, reddit | No Comments »

I was that bust of Thanos on here and had to paint one. Printed 50% scale at .06mm layer height on a stock Ender 3.

submitted by /u/bigmanmac14 [link] [comments] from 3D printing news https://ift.tt/2B8479e via RSS

Tags: , , , ,

Posted in 3D, 3DPrinting, news, reddit | No Comments »

Simplest 3d modeling software.

Hi guys what's the most user friendly software to use when designing a model? submitted by /u/Coilheadfesigns [link] [comments] from 3D printing news https://ift.tt/2vGtgmi via RSS

Tags: , , , ,

Posted in 3D, 3DPrinting, news, reddit | No Comments »

Losing my mind over my Ender 3’s bed leveling.. Need some advice!

So my Ender 3 has a warped bed, where it dips in the middle and after all of the corners are the same height it is way lower in the middle. After finally finding a correctly sized glass bed I purchased it. After installing it I adjusted the end stop to accomodate the new glass, however I still can't get …Continue reading →

Tags: , , , ,

Posted in 3D, 3DPrinting, news, reddit | No Comments »

Geen tijd voor een huisdier? Neem een huisrobot! (zie mancave.conrad.nl)

Veel mensen willen wel een huisdier, maar hebben hier eigenlijk geen tijd voor. Een hond moet drie keer per dag uitgelaten worden. Een kat zijn nagels moeten worden geknipt. En het isĀ  natuurlijk wel zo leuk als er eens in de zoveel tijd iemand bij het dier is. Puur om te voorkomen dat hij of zij eenzaam wordt. Vervolgens moet …Continue reading →

Tags: , , ,

Posted in Dutch, DYI, mancave, NL | No Comments »

My first ever 3D print! Creality Ender 3 with Filament Friday gray PLA. Album in comments.

submitted by /u/jclear [link] [comments] from 3D printing news https://ift.tt/2OAV42t via RSS

Tags: , , , ,

Posted in 3D, 3DPrinting, news, reddit | No Comments »

Anet A6 z motor calibration

Has anyone had issues with one of two z motors not moving at the same rate. The z motor opposite to the limit switch(right side) climbs faster than the left.but I think it might be why when I print at .3 I have such terrible layer lines. I understand it's not supposed to look great but it looks way worse …Continue reading →

Tags: , , , ,

Posted in 3D, 3DPrinting, news, reddit | No Comments »

[question] Specs for a basic, basement workbench pc for F360/slicing

I'm well versed in building PCs but generally aim for top performance for gaming. So my views on hardware can be a bit skewed and cost can runway with me pretty quick. Right now I use my desktop gaming pc for F360 and Slic3r/Formware slicers for 3d printing. But it can be a bit of a pain in the as …Continue reading →

Tags: , , , ,

Posted in 3D, 3DPrinting, news, reddit | No Comments »

SSJ3 Goku Ender 3

submitted by /u/SSJedi1 [link] [comments] from 3D printing news https://ift.tt/2MvMc0J via RSS

Tags: , , , ,

Posted in 3D, 3DPrinting, news, reddit | No Comments »

Check out this great gadget!